Email:
Tel:+8675586718316
Our new customers from Taiwan( Republic of China) placed the order on one(1*) pcs of machine: Model YX-WK01-30B banding machine for paper notebook boxes etc.
For all the machines purchased it is clear to confirm all the information on the products so we often ask our customers to freight the samples to test and commission the machines in order that the machines and customer's products gains the best compatibility and adaptability.
After getting the confirmation &samples of the product in sizes and drawing for manufacturing the banding paper machines
we spent only 7 working days finishing everything and made the machines ready after testing them in a satisfactory feedback.
Recently our customers sent us the positive commentar on the machines which keep running very well in their factory ever since the machines arrived their factory.
The machines was shipped via DHL courier to Chiayi . The documentaries certificated with ISO&CO&CE together with other files necessory are sent via DHL to customer for assisting customers to clear the custom.
As below there listed the basic information on the successful transaction between PENGLAI and their Taiwanese counterpart:
Purchased order issued &Key communiction points During Business Discussion:
Samples sent from customers in East Asia
Bank copy of Down&balance payment for purchasing Benchtop banding machine semi automatic model YX-WK01-30B
Testing videos on Semi automatic banding machine semi automatic tabletop type bander:
Wooden case packing of benchtop type banding machine
As follow there given the description on the machines purchased respectively
The paper bands banding machine is widely used for kinds of industries, such as medicine food, printing, cloth, journey, vegetables etc, which can strap big-sized box together and also wrap hard or soft products with multi-PC and multi-pack.
Features of benchtop paper banding machine hotmelt
1.Strapping diversification: Includes single straps, double straps, three straps, well type straps etc.
2.Strapping speed fast: It takes only 3 seconds to finish one strapping, which integrate press, tight, scaled cutter for one time.
3.High quality and low cost, more economical
4.Strapping function is better for heat sensitivity.
5.Touch screen: Adopt PLC control program, touch screen can adjust or operate about parameter, set convenient button and reach four model including handle, automatic, temporary stop, stick. All will satisfy users request.
Basic parameters of model YX-WK01-30B tabletop banding machine:
|
Model Number |
YX-WK01-30B |
| Binding tape width | 30mm paper tape or OPP tape |
| Binding tape length | 150m |
| Max binding size | 470*200MM(W*H) |
| Min binding size | 30*10mm(W*H) |
| Binding tape inner diameter | 40mm |
| Binding tape external diameter | 155mm |
| Binding speed | less than 2.5s per bundle |
| Binding tension | 5-50N |
| Binding way | hot heat to seal |
| Power | AC220V/50Hz/80W |
| Weight | 32KG |
| Volume | 596*364*504mm |
Note: Previous improvements or improvements to mechanical specifications,
dimensions will not be explained separately.
More detailed pictures on tabletop banding machine model YX-WK01-30B:
Repair and maintenance
Problem 1：not working
|
NO. |
Possible reasons |
Solutions |
|
1 |
Safety switch not closed
|
The right door is not closed and the safety switch contacts are not pressed
|
|
2 |
No fuse or damage inside the socket
|
Replace the fuse |
|
3 |
Loose socket, plug or power cord
|
Check power supply and connection device
|
|
4 |
Circuit boards defected |
Detect or replace the board |
Problem 2：Tape cutting abnormally
|
NO. |
Possible reasons |
Solutions |
|
1 |
Medium knife blade or front blade wears too much
|
Replacement |
|
2 |
Loosening screw
|
Tighten the front head screw
|
| 3 |
Medium knife blade and front knife pressure is too small
|
Adjust the tightening screw pressure in the middle seat (the pressure of the two screws is even when adjusting, the pressure should not be too large, and the middle knife will not fall too much) |
Problem 3：Tape in stuck or make crease
|
NO. |
Possible reasons |
Solutions |
|
1 |
Over force of the bindling |
Force decrease |
|
2 |
The belt slot and the drive wheel gap are too large
|
Adjust the gap, the gap is ≤0.2
|
|
3 |
There are burrs or foreign objects in the groove
|
Clean up burrs or foreign objects
|
|
4 |
There are burrs or foreign objects in the belt slot
|
Clean up burrs or foreign objects
|
Problem 4：Tape can not close well
|
NO. |
Possible reasons |
Solutions |
|
1 |
The proximity switch does not detect the signal
|
1. The contact does not reach the last position ； 2. The proximity switch position is too close
|
|
2 |
Motor failure
|
Check if the motor or wiring is normal
|
Problem 5：Tape can not feed
|
NO. |
Possible reasons |
Solutions |
|
1 |
The proximity switch detects the signal
|
1. The contact is not returned. 2. The proximity switch position is too far.
|
|
2 |
There are burrs or foreign objects in the groove.
|
Clean up burrs or foreign objects.
|
|
3 |
Motor failure
|
Check if the motor or wiring is normal
|
|
4 |
The drive wheel has friction with the grooved plate.
|
Adjusting the front and rear position of the drive wheel makes it flexible.
|
Problem 6：Tape can not through the groove stably
|
NO. |
Possible reasons |
Solutions |
|
1 |
The guide groove is unevenly
|
adjusted to level the front and rear guide grooves at the same horizontal direction.
|
|
2 |
Misalignment of the interface with each slot |
The slotted interface is higher than the slotted interface
|
|
3 |
The interface gap between each segment and slot connection is too large |
Adjust the gap≤2.5 |
Mantainence
1. Turn off the power after resetting the machine before maintenance.
2. It is recommended to clean the inside of the machine after packing every day. The main performance is the dust inside the machine. Please use the air gun with a pressure less than 0.1MPa to remove the dust at the bottom of the machine and the dust at the three cutter poles.
3. Regularly check the power cord and electrical components for damage and looseness.
4. Regularly check whether the moving parts such as the blade, rocker arm, skateboard and arbor are seriously worn.
5. Regularly check the bolts and nuts for looseness.
6. Regularly lubricate moving parts. Especially when the machine is not used for a long time, it should be lubricated with lubricating oil in the sliding part to achieve flexible effect. Add 2-3 drops of lubricant each time.
Refueling parts as shown below:
1. Add the lubricating oil once a week to the arbor, chute and driven wheel frame of the three knives (or lubricate the lubricating oil when the knives are not falling), and remove the parts without adding lubricant.
2. The bushing and shaft moving piece need to be lubricated once a week.(Or when the frame is not flexible, it should be lubricated in time), and there are four places before and after.
Wooden case packaging for tabletop banding machine:
Vertical paper &OPP bands banding machine can used with large paper in width 50MM and the product size with Wdith more than 500MM*Height 200mm
ALL RIGHTS RESERVED by ®SHENZHEN PENGLAI INDUSTRIAL CORPORATION LIMITED
